Showing posts with label End Time Preparation. Show all posts
Showing posts with label End Time Preparation. Show all posts

‎10 imp drug interactions:

‎10 imp drug interactions:

No comments
By Unknown

1)Fluoxetine and Phenelzine
The interaction can result in a central serotonin syndrome.(3)This condition is characterized by mental status changes, agitation, diaphoresis, tachycardia, and death. These symptoms can develop quickly with only 1 or 2 doses of fluoxetine when combined with phenelzine. Serotonin syndrome is possible with any monoamine oxidase inhibitor (MAOI), such as phenelzine or tranylcypromine sulfate, in combination with any drug that increases serotonin levels, such as dextromethorphan, meperidine, and other selective serotonin reuptake inhibitors (SSRIs).(3)It is recommended that fluoxetine be stopped for at least 5 weeks before an MAOI is prescribed because of the long half-life of fluoxetine and its primary metabolite, norfluoxetine. Also, 2 weeks should be allowed after discontinuation of an MAOI before starting SSRI treatment.(3)

2)Digoxin and Quinidine
This significant drug interaction has been known for a long time, yet it continues to be a problem, often with devastating results. The interaction can lead to a marked increase in plasma concentration levels of digoxin in more than 90% of patients.(4)Significant changes in serum digoxin are noticed within 24 hours. The average increase is roughly 2-fold.(5)The effects from this interaction range from nausea and vomiting to death. The primary mechanism for this interaction is a decreased volume of distribution of digoxin, secondary to its displacement from binding sites in body tissues.(4)Quinidine also decreases renal and nonrenal excretion rates of digoxin, which leads to increased steady-state concentrations of the cardiac glycoside.(4)Ideally, patients taking digoxin should avoid the use of quinidine; however, if the combination is necessary, the patient should be closely watched. Pharmacists should anticipate the need to reduce the digoxin dose by one half.(4)

3)Sildenafil and Isosorbide Mononitrate 
Sildenafil may markedly increase the hypotensive effects of isosorbide mononitrate.(6)More than 123 deaths have been reported since 1998, when sildenafil was made available in the United States.(6)Most deaths were among patients with 1 or more risk factors, including obesity, hypertension, and cigarette smoking. Sildenafil was developed as a phosphodiesterase-5 (PDE5) inhibitor. In the presence of PDE5 inhibitors, nitrates can cause intense increases in cyclic guanosine monophosphate and dramatic drops in blood pressure.(7)Patients taking isosorbide mono-nitrate or any nitrate, including nitroglycerin, should be advised not to take sildenafil.

4)Potassium Chloride and Spironolactone
This is another significant drug interaction that has been known for a long time. The combination may result in hyperkalemia.(8)The resulting hyperkalemia can be serious and may lead to cardiac failure and death. Patients with renal impairment are especially prone to this effect. Spironolactone is a competitive antagonist of mineral corticoids, of which aldosterone is a potent example.(9)This mechanism occurs in the kidney at the distal portion of the nephron and leads to the excretion of sodium ions while saving potassium ions.(9)Patients receiving potassium-depleting diuretics, such as amiloride or triamterene, may also experience this interaction. These diuretics can interact with all absorbable forms of potassium?bicarbonate, citrate, acetate, gluconite, and iodide salts.(9)Severe hyperkalemia is dangerous, and thus patients who are prescribed spironolactone must undergo an evaluation of serum potassium levels.(9)

5)Clonidine and Propranolol
The combination may produce a mysterious hypertension that is unrelated to the pharmacology of either agent when administered independently.(8)A sudden withdrawal of clonidine from adjunctive therapy with propranolol may cause fatal rebound hypertension.
Clonidine is a central alpha-2 adrenergic agonist that suppresses the sympathetic nervous system from the brain.(10)This activity leads to a decrease in the norepinephrine amounts available in the synaptic cleft of the adrenergic neuron. Alpha-1 receptors then become sensitized because of less norepinephrine available in the cleft.(10)When clonidine is suddenly withdrawn, the result is a large increase in norepinephrine in the synaptic cleft of the adrenergic neuron. The sensitized alpha-1 receptors are stimulated, leading to an exaggerated vasoconstriction. The body cannot compensate for this response because the beta-2 receptors are blocked when a patient is concurrently taking propranolol. Within 24 to 72 hours, a dramatic rebound hypertension is noticed.(9)

6)Warfarin and Diflunisal 
Nonsteroidal anti-inflammatory drugs (NSAIDs), such as diflunisal, have been shown to increase the risk for gastrointestinal (GI) bleeding and the anticoagulant response of war-farin.(5)Other NSAIDs?such as keto-profen, piroxicam, sulindac, diclo-fenac, and ketorolac?have been shown to have similar interactions with warfarin. In most patients, however, indomethacin has little effect on hypothrombinemic response.(5)Because the interaction between warfarin and diflunisal can lead to GI bleeding or even fatal hemorrhaging, an alternative to diflunisal is suggested. Acetaminophen is the alternative of choice. Yet, if an NSAID is needed, nonacetylated salicylates?such as magnesium salicylate or salsalate?are safer because of minimal effects on platelets and gastric mucosa.(5)

7)Theophylline and Ciprofloxacin
Concurrent administration may lead to toxic increases in theophylline.(11)This problem occurs because the hepatic metabolism of theophylline is inhibited by ciprofloxacin via the cytochrome P-450 enzyme system. Theophylline is metabolized by CYP1A2 and to a lesser extent by CYP3A4. Ciprofloxacin and other drugs, including clarithromycin, erythromycin, fluvoxamine, and cimetidine, are all potent inhibitors of CYP1A2. Because they have little effect on CYP1A2, levofloxacin or ofloxacin should be considered as an alternative to ciprofloxacin.(5)Theophylline toxicity is a serious condition; several deaths have been linked with serum concentrations as low as 25 mcg/mL.(11)Signs of theophylline toxicity include headache, dizziness, hypotension, hallucinations, tachycardia, and seizures.(11)

8)Pimozide and Ketoconazole
Pimozide alone can prolong the QT interval, and it has been linked with ventricular arrhythmias (torsades de pointes).(5)When pimozide is combined with ketoconazole, the combination can be deadly. Pimozide is a CYP3A4 enzyme substrate, and ketoconazole is a potent inhibitor of CYP3A4. This leads to marked increases in pimozide serum levels.(5)Other drugs?such as itraconazole, clarithromycin, erythromycin, diltiazem, and nefazodone?are also potent inhibitors of CYP3A4 and should not be administered with pimozide.(5)Fluconazole is weaker, but in larger doses it also inhibits CYP3A4. Terbin-afine is a safer choice because it does not affect CYP3A4.(5)

9)Methotrexate and Probenecid
When probenecid is administered with antineoplastic doses of metho-trexate, the result can be a 2- to 3-fold increase in methotrexate levels.(5)Probenecid acts as an active tubular secretion inhibitor and prevents methotrexate from being excreted, thus potentially causing toxicity. The symptoms of severe methotrexate toxicity include diarrhea, vomiting, diaphoresis, and renal failure, and it may result in death.(9,12)This interaction with methotrexate also occurs with penicillins (eg, amoxicillin, carbeni-cillin) and salicylates.(5)The risk with low-dose methotrexate (commonly used for arthritis) is lower; in fact, NSAIDs in combination with low-dose methotrexate are often prescribed purposely.(5)
Possible alternatives include aceta-minophen, as opposed to salicylates or NSAIDs. Celecoxib does not affect methotrexate pharmacokinetics and could be an alternative. However, rofecoxib produces some increases in methotrexate serum concentrations and therefore should be avoided.(5)

10)Bromocriptine and Pseudoephedrine
The interaction can lead to severe peripheral vasoconstriction, ventricular tachycardia, seizures, and possibly death.(5,13)Bromocriptine is an ergot-derived dopamine agonist with several uses, including antiparkinsonian therapy. New treatment guidelines for Parkinson?s disease recommend a first-line therapy change from levodopa to bromocriptine or other dopamine agonists, such as ropinirole, pramipexole, or pergolide.(14)Notable side effects of bromocriptine include thickening of bronchial secretions and nasal congestion.(11)This is significant because it increases the likelihood of a patient taking bromocriptine to self-medicate with an OTC decongestant such as pseudoephedrine. Patients receiving bromocriptine should be advised to avoid all sympathomime-tics.(5) 

Microscopy of some impotant drugs

Microscopy of some impotant drugs

No comments
By Unknown

1-Liquorice- Ulignified Septate fibre
2-Solanacoeus Plants- Anisocytic stomata
3-Rhubarb- Star spots
4-Squill- Ca oxide raphides
5-Cardamom- Clothing of glandular trichome
6-Quillaria- Thin membrane arillus
7-Digitalis- Rhytidomes & Glandular Trichomes
8-Atropa Belladona- Anisocytic Stomata
9-Verbascus Thapsus- Clusters of Ca Oxalate
10-Artemisia- T-Shaped Trichomes
11-Stromanium- Phloem Fibres
12-Nuxvomica – Lignified trichomes
13-Fennel- Reticulate lignified trichomes
14-Coriander- Wavy sclerenchyma
15-Indian Dill- Lateral ridges with vascular bundle
16-Anise- Branched & unbranched vittae
17-Cinnamon- Absence of cork & cortex
18-Ginger- Non Lignified vessels & starch grains , Endodermis with no starch
19-Collapsed Endodermis
20-Caraway-Collapsed Parenchyma
21-Chenopodium-Epidermis with no trichomes
22-Chirata- Stomata on lower surface only with no trichomes
23-Cinchona - Large sclerenchymatous bast cells with Medullary ray.
24-Cinnamon- Parenchyma cells with starch.
25-Colchicum- Spiral Ducts, Parenchyma with starch
26- Coriander- Prismatic and aggregate crystals of calcium oxalate
27-Saffron- Trichome of stigma
28-Turmeric- Parenchyma with pasty starch
29-Digitalis- Glandular trichomes
30-Euclyptus- Crystal bearing fiber
31-Gentian- Large reticulate ducts
32-Liquorice- Parenchyma with crystals and starch
33-Hycyamus- Endosperm tissue with proteid granules and oil.
34-Ipecac- Parenchyma with raphides
35-Mentha- Trichomes, simple, showing cuticular markings (a medium sized trichome).
36-Pilocarpus- Aggregate crystals of calcium oxalate.
37-Podophyllum- Reticulate ducts and tracheids, Spiral duct, Aggregate crystals of calcium
oxalate, Cork
38-Quassia- Medullary ray with starch, Large porous duct
39-Rheum- Parenchyma with starch, resin and crystals, Reticulate ducts.
40-Senega- Parenchyma with fat, Cork & Porous duct.
41-Senna- Bast of vascular bundles, Crystal bearing fibers from vascular tissue
42-Stromanium- Parenchyma cells of petiole
43-Strophanthus- Endosperm tissue, showing oil and crystals, Outer tissue with granular proteid
matter and starch
44-Tobbaco- Parenchyma (collenchymatous) from midrib,Leaf parenchyma with chlorophyll.
45-Ginger- Parenchyma with starch and one cell with resin
46-Belladona- Tracheids and spiral duct, Leaf parenchyma cells with crystals,Bast Cells, Porous
ducts & Crystal Sand
 

Drugs And Their Analogues

Drugs And Their Analogues

No comments
By Unknown

Drug - analogue

zidovudine -thymidine
Didanosine-deoxyadenosine
Lamivudine-cytosine
Stavudine-thymidine
abacavir-guanosine
Ganciclovir-acyclic analogue of guanosine
zalcitabine-homologue of cytosine
Foscornet-pyrophosphate
Tribavirin-guanosine
Sulphonamide- PABA
mithotrixate & folate = pteridin
Streptomycin = streptidin
Gentamycin = deoxy streptamine
Aztreonam = mono bactam
Cephalosporin = cepham
Merapenam , imipenam = carbapenam
Clavulanic acid = OXAPENAM
Pencillin = penam
Ethacrynic acid = phenoxy acitic acid
Metrindazole = 1,2,4 thiazolidin
amiloride = pyrazin & guanidin
Spiranolactone = thioacetic acid at 6th position
atorvastatins-pyrrole
fluvastatins-indole
cerivastatins-pyridine
rosuvastatins-pyrimidine
fibrates-isobutyric acid derivatives
aziritidine-ezetimibe
pyrazine-acipimox
acetazolamide-1,3,4-thiadiazole
thiazide-1,2,4-thiadiazine
 

Revision Of TABLETS

Revision Of TABLETS

No comments
By Unknown


TABLETS
  • 90% of drugs are in oral dosage form.
  • Tablet is unit dosage form.
  • Liquid dosage forms r given in dose of medication 5-30%.
  • Tablet should have 2-4% of moisture.

Evaluation
  • General appearance
    • Size and shape – compressed tablets shape and dimensions are determined by the tooling during the compression process.
Rem-when compression force is constant, tablet thickness varies with changes in die fill, with particle size distribution, packing of particle mix and tab. Weight.
When die fill is constant, thickness varies with variation in compressive load.
*         Crown thickness of tablet measured by micrometer.
*         Total crown thickness is measured by vernier calliper.
*         Tablet thickness should be controlled with ±5% of std. Value.
*         The more the convex the tablet surface more is the capping problem so one has to use slower tablet machine or one with pre compression capabilities.
*         Unique identification markings-given in Physicians Desk Reference(PDR).
*         Product code is given from National Drug Code (NDC).
*         Mottling-non uniformity of colour over tablet surface.
*         For colour quantification 3 methods-reflectance spectrophotometry, tristimulus colorimetry and micro-reflectance photometry.



  • Hardness and Friability
    • Hardness of tablet directly effects dissolution behaviour.
    • It is the force req. to break the tablet in diametric compression test.
    • Hardness also called crushing strength.
Devices used
*         Monsento tester (stockes tester)-easy to handle.Manually operated,gives strength in kgs.
*         Strong-cobb tester-force applied by hydraulic pressure and later air pressure not manually. It gives value 1.6 times higher than the original strength. it gives strength in kgs.
*         Pfizer tester-same principle as pair of pliers.(kgs)
*         Two testers to eliminate operation variations:-
1.Erweka tester-gives strength in Kgs.
2.Schleuniger tester-operates in horizontal position-gives strength in KGs and Strong Cobb units.
  • Hardness and thickness of tablet is a function of die fill and compression force.
  • At constant compression force, hardness increase with increasing die fill.
  • At constant die fill, hardness increase and thickness decrease when compression force is applied.
  • Roche friabilator machine is used for measuring friability of tablet.
Tablets fall from-6 inch distance
Total Rpms-25
Total revolutions-100
Time-4 minutes
Limits-0.5-1.0% (USP),not more than 1% (IP).
  • Effervescent tablets and chewable tablets show higher friability value than above so stack packaging for them.
  • Vickers test is used to measure the surface hardness.
  • ‘Whiskering’ phenomenon is related with tablets with deeply concave surfaces or punches used were in poor condition and such tablets have higher than normal friability values.
HARDNESS LIMITS
TABLET
HARDNESS LIMIT
SOFT
2 KG
SUSTAINED RELEASE
8 KG
GENERAL
4 KG
HARD
6 KG
EFFERVESCENT
1.3 KG

STANDARD HARDNESS SHOULD BE MIN. 4 KG

  • Webster and Van Abbe tester-indicate edge damage during handling.
  • Weight variation
    • Total tablets taken-10.
    • Limits-Tablets meet USP if not more than 2 tablets are outside the limit and no tablet should differ by more than 2 times the original limit.
    • This test is used if the tablet contains 90-95% API. It is not appropriate for low dose containing tablets.API should be more than 50mg. (i.e-potency). For these content uniformity test is used.
Average wt of tablets(mg)
Max. % diff. allowed
130 or less
10
130-324
7.5
More than 324
5

I.P limits
Average wt of tablets(mg)
Max. % diff. allowed
80 or less
10
80-250
7.5
More than 250
5

CONTENT UNIFORMITY TEST:
  • It should be between 95-105%.
  • Tablet potency for this test should be less than 50mg.
  • For digitoxin it is 90-110%.
  • If  larger wt. Variation ,no good content uniformity.
Test:
Total tablets-30
Total assayed-at least 10
9 of the tablets should contain 85-115% API.10th tablet may contain 75-125% API. Test passed
If above conditions not met other 20 tablets should be assayed, and no one should fall outside 85-115% range.
  • Disintegration

  • Apparatus:-
-6 test tubes
-mesh size:10 mesh i.e 1.7mm(USP),8 mesh i.e 2mm(IP)
-glass tubes are 3 inches long
-beaker contains 1L of water, simulated gastric fluid or simulated intestinal fluid.
-temperature: 37±2 degree Celsius. (Remember with reference to difference with dissolution)
-tablets remain 2.5 cm below surface of liquid on upward movement and vice versa.
-no. of cycles per minute:28-32

                                                          IP LIMITS
Tablet/Capsule
liquid
Disintegration time(min)
Uncoated tablet
water
15 min (USP-30 min)
Sugar coated
water
60 min
Enteric coated
0.1N HCl with phosphate buffer
2 hr in gastric fluid media and 1 hr in intestinal fluid(USP it is reverse)
Film coated
Water or 0.1N HCl
30 min
Vaginal tablets
water
30 min
Soluble, dispersible and effervescent tablets
Water
(19-21 deg. Celcius)
3 min
Hard gelatin capsules
water
15 min
Soft gelatin capsules
water
60 min







  • Dissolution
USP
Apparatus 1-Basket type
  • Mesh screen-10 mesh(USP)
  • -temperature: 37±0.5 degree Celsius.
  • 900 ml flask.
Apparatus 2-paddle type
  • 900 ml. Flask.
  • Contains wire helix to prevent tablet from floating.
Limits(USP)
ü  Not less than 75% should be dissolved in 45 min.
ü  90% of the drug should be dissolved in 30 min.(this is not USP limit, it is industrial limit)
ü  Above both values are Q values.
ü   
Dissolution acceptance criteria(IP)
stage
No. Of dosage units tested
Acceptance criteria
S1
6
No dosage unit is less than Q+5%.
S2
6
Average of 12 dosage units is equal to or not more than Q% and no unit is less than Q-15%.
S3
12
Average of 24 dosage units is equal to greater than Q% and not more than 2 dosage units are less than Q-15% and no dosage unit is less than Q-25%.


  • Tablet compression apparatus
    • Dies define shape and size of tablet.
    • Cam tracks guide the movement of punches.
    • Multi-station presses are called rotary presses.
    • Turrets-the portion of the head that hold the upper and lower punches.
    • Fette machines-they chill the compression components to allow compression of low melting solids such as waxes use (in case of suppositories0.

TOOLING
  • BB tooling-most commonly used.length-5.25 inch,nominal barrel diameter-0.75 inch,1 inch head diameter.
  • B tooling-5.25 inch, nominal barrel diameter-3 9/16 inch,1 inch head diameter.
  • D tooling-used for larger tablets. 5.25 inch, nominal barrel diameter-1 inch,1.25 inch head diameter.
  • Dwell time-time for which tablet remains under compression.
  • Remember-Devices which measure compression force at each compression station.
-Pharmakontroll, Killiani Control System, Thomas Tablet Sentine


  • PROCESSING PROBLEMS IN TABLET
1)       Capping and lamination-capping is partial or complete separation of top or bottom parts of tablet from main body of tablet.Lamination is separation of tablet into 2 0r more distinct layers. It is due to:-
- deformational properties of formulation i;e plastic deformation
-deep concave punches.
- absence of adequate moisture.
-tablet tooling
-incorrect setting of press.
 2) picking and sticking-picking occurs due to engraving and embossing.In  sticking tablet material sticks to die wall.
 3) Mottling-uneven distribution of color on tablet.
4) wt. Variation
5) poor flow-talc or colloidal silica helps in improving the flow.poor flow can result in bridging,arching and rat holling.
6) poor mixing
7)punch variation
8)hardness variation
9)double impression

  • TABLET GRANULATION
    • It improves flow properties of tablet.
    • Shape factor of granule should be 6 just like sphere for good flow.
    • The method used for measurement of surface area solid granules or particles are air permeability method and gas-adsorption method(He gas is used).
    • Dense granules require higher compression force to form cohesive compact and they are less friable.
    • For determining granule density-Mercury displacement method is used. O                                       ther method uses benzene as organic solvent.
    • As granule size increase bulk density decreases.
      As particle becomes more spherical bulk density increases.
    • The strength of tablet is mainly due to surface tension of liquid and capillary forces.
    • For measuring granule strength and friability ASTM(American Society For Testing Materials) specification is taken into account and compression strength are taken into account.
  • TYPES OF GRANULATION
    • Dry granulation
*         Also called compression granulation.
*         Used when drug is sensitive to moisture.
*         Slugs are formed in this.so process also called slugging.
*         Roller compactor instrument is used.Can produce 500 kg of slugs.
*         Main advantage is that no need to use excess lubricants.
  • Wet granulation
*         Granules formed by adhesive forces.
*         Surface tension forces and capillary pressure are initially responsible for wet granulation.
*         Solvents are used considering EPA(Environmental Protection Agency) regulations.

EQUIPMENTS FOR WET GRANULATION
  1. 1.        Littleford Lodige mixer- capable of both wet massing and blending.
*         Time taken-30-60 sec.
*         Horizontal in operation.
*         Temperature rise of 10-15 deg. is expected.
2. Diosna mixer or granulator-contains bowl in vertical position.
*         Total time 11-12 min.
3. Littleford MGT mixer-vertical in operation.
4.Gral mixer-modification of planetary mixer(IMP).

  • Direct compression
*         E:g Nacl,KCl can be directly compressed.
*         Uses directly compressible diluents like spray dried lactose.
*         They have good flow and compressibility.
*         Maximum of 30% of API is used in direct compression tablet.

  • TABLET INGREDIENTS 
    • Diluents:
*         Used to increase bulk of tablet.
*         5-80% can be used.
*         All the sugar containing diluents have tendency to undergo reaction with drugs containing –NH2 group. This is called Maillard reaction which only changes color not content.
STARCH
ü  11-14% moisture present
ü  Dried starch has 2-4% moisture. Their moisture level increase to 6-8% following moisture exposure.
ü  Two types:

Directly compressible starch (Sta-Rx 1500)-used as diluents, binder and disintegrant.
Contains 10% of moisture.
Hydrolysed starch (Emdex, Cellutab: contain 90-92%dextrose and 3-5% maltose)-directly compressible. Used in chewing tablets and have 8-10% of moisture.

LACTOSE
  • Three types of lactose.
  1. 1.        Alfa-lactose monohydrate-crystalline nature, has 5% moisture, poor flow and compressibility and used in wet granulation. It gives Maillard reaction.
  2. 2.        Spray dried lactose-<3% moisture.good flow and compressibility. Used in direct compression.it gives Maillard reaction.(in Maillard reaction furfuraldehyde is formed).
  3. 3.        B-lactose(anhydrous)-hygroscopic. used in direct compression and does not gives Maillard reaction.

DEXTROSE
  • Also called cerelose.
  • Can be used instead of lactose.

MANNITOL
  • Used in chewable tablet due to negative heat of solution.
  • Non-hygroscopic.
  • Non-cariogenic.
  • Used in vitamin formulations.

SORBITOL
  • Optical isomer of mannitol.
  • Hygroscopic.

SUCROSE
  • Available as co-processed form such as SUGARTAB(90-95%sucrose + 7-10% invert sugar), DIPAC(97%sucrose + 3% modified dextrins) and NUTAB(95%sucrose+4%invert sugar+Mg.stearate+corn starch).
  • Used in direct compression.
  • Hygsroscopic

Important point-Kaolin and bentonite,diluents, is not used with cardiac glycoside,synthetic estrogens and alkaloids                           
                                                                MICROCRYSTALLINE CELLULOSE
  • Trade name-AVICEL
  • DIRECTLY COMPRESSIBLE
  • Two grades:-PH101(powder) and PH102(granules)
  • Also act as disintegrating agent.
  • Hygroscopic
  • May delay the release of drug.

DICALCIUM PHOSPHATE
  • Non-hygroscopic(just like mannitol)
  • Moisture sensitive drugs can be used with it
  • Not used with tetracycline due to complex formation.

Classification in other way

Wet granulating diluents-alfa lactose,kaolin,bentonite, dicalcium sulphate
Direct compression-spray dried lactose,colloidal silica,NaCl and NaHCO3 for dental cones, direct com. starch.

Binders and adhesives
  • Used to provide cohesive qualities.
  • More the binder, harder is the tablet.

NATURAL GUM

  • Acacia and tragacanth are examples
  • Used in 10-25%

GELATIN
  • Natural protein
  • 10-20% in solution form.
  • Upon storage disintegration time will increase with the use of such binders
Starch
  • 10-20%solution.
  • Give translucent paste.
  • It undergoes hydrolysis to dextrin and glucose.
  • Liquid glucose is 50%solution in water.
Modified natural polymers
  •  Methylcellulose(alcohol soluble, more soluble in cold water than hot water)
  • Hydroxy propylcellulose(alcohol sol.)
  • Hydroxy propyl methylcellulose(water soluble)
  • Ethylcellulose(alcohol soluble,retard D.T)
  • PVP(polyvinyl pyrrolidone) used in 2%.used in aqueous and alcoholic solution.
  • IPA(isopropyl alcohol)-widely used binder.

  • Another classification
ü  solution binders-strach,sucrose,gelatine,acacia,tragacanth.
ü  Dry binders-HPMC.Cross linked PVP.

  • LUBRICANTS
ü  Decrease friction between diewall and tablet surface
ü  Can be used intragranularly(PEG,Vegetable oils) and extragranularly(talc,stearates).
ü  They are hydrophobic in nature.
ü  Fluid lubricant-liq. Paraffin
ü  Boundary lubricant-stearic acid
ü   
  • What is bolting of lubricant?
Lubricant is passed through 60-100 mesh nylon cloth in order to get fine particles this is called bolting of lubricant.

ü  Hydrocarbon/mineral oil
  • Applied as fine spray.
  • Mostly used for aspirin tablets
ü  Calcium and Mg. Stearate
  • used in 1%
  • may cause delay release

ü  Mg.stearate is used with SLS due to its hydrophobic property.
ü  It is not used with acidic drugs

                     
  • Compritol 888
ü  It is glyceryl monoester of behenic acid.

  • Water soluble lubricants
ü  Sodium enzoate,sodium acetate,NaCl,leucine,PEG etc.

  • GLIDANTS
1)       Talc
  • Used in 5%.
  • Can also be used as anti-adherent.
  • Contains traces of iron so may act as catalyst for the drugs which are degraded by Fe.
  • Also contain calcium so not used with tetracycline.

2)       Colloidal silica
ü  Available in 3 forms
ü  Cab-o-sil(<1%)
ü  Aerosil(0.25-3%)
ü  Syloid.

Corn starch
ü  Use in 5-10%


                                                                                DISINTEGRANTS
  • Facilitate breaking up of tablet
Act by 3 mechanism
  1. 1.        By swelling
Alginate, starch dye, PVP
  1. 2.        By wetting
SLS, Clay, Bentonite

  1. 3.        Effervescent
NaHCO3 and citric acid

Examples
STARCH
ü  5-20%
ü  Modified starches are used which are: Primogel and Explotab. they are low substituted carboxymethyl starches.(1-8% used,but 4%is optimum)

  • Clays
ü  Veegum (Mg. Aluminium silicate)(10%)
ü  bentonite(10%)
  • both are used only for colored tablets
  • they are most effective in sulfathiazole tablets.
    • Super disintegrants
ü  They are used in lower concentration. of 2 % to 6 %,while traditional disintegrants such as starches often require concentrations of about 20 %. 

  
Sodium Starch Glycolate

  
Sodium Carboxymethyl Starch
  
Croscarmellose Sodium

  
Soy Polysaccharides
  • Primojel®, sodium starch glycolate, and Primellose®, croscarmellose sodium, which show outstanding disintegration characteristics for tablets prepared by direct compression, wet granulation and for capsule formulations.  

COLORING AGENTS
ü  Lake are the dyes that have absorbed on hydrous oxide
ü  As coloring concentration increases, mottling increases.
ü  To improve photosensitivity of dye use of UV absorbing chemical such as benzophenone can be used.

v  DI-PACLINE is a commercially available directly compressible sugar.

SWEETENERS
ü  Used in (0.5-0.75%)
ü  Cyclamates can be used.they are 70 times more sweeter than sugar. But are carcinogenic
ü  Aspartate(phenyl ester of methylacetic acid).180-200 times sweeter than sugar and non-carcinogenic.
ü  Saccharin is carcinogenic and 500 times more sweeter than sugar.
ü  Mannitol is used in chewable tablets and 72 times more sweeter than sugar.

SOME INSTRUMENTS
MIXING
ü  For large qt. Of powder-twin-shell blender,double-cone blender,planetary mixer.
ü  For continuous production-ribbon blender,roto cabe-blender
ü  Mass mixer-sigma blade mixer
ü  High speed granulators-Diosna mixer,Littleford MGT,Gral mixer

ü  For continuous production extruders are used E:g Reitz extruders
ü  Topo granulators-to prepare granules under high vaccum.

ü  Spheronization-refers to formation of spherical particle from wet granulation.
ü  Marumerizer and CF-granlator are used for spherozination

  • Spray congealing/spray chilling
ü  It is the process consist of melting solid and reducing them to beads or powders by spraying molten feed into stream of colder air or gases.

ü  Monoglycerides are spray congealed at 50 deg F
ü  Carbohydrates are sparay congealed at 167 deg F

  • Important information
ü  Versa press is used for the the preparation of layered tablets.
ü  Manestey dry cota instrument is used.implantation tablets should have size of less than 8mm.
ü  Kern-injector-contain hollow needle and plunger. used for administration of rod shaped tablet.
ü  For sub-lingual and vaginl tablets, lactose is used as diluent.

About the Author

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Pellentesque volutpat volutpat nibh nec posuere. Donec auctor arcut pretium consequat.

Proudly Powered by HiReN.